01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 1TCSAttachment, Setup, ServiceGeneral notes ...
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 10TCSTechnical modificationsDesig-nationFeature Effective fromnone Retaining pins. Top mate
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 11TCSUpgrading to type IIUpgrading from type I to type II is only possible under certain co
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 12TCSFig. 5: Material guide plate. Left side: type I; right side: type II.Fig. 6: Cable str
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 13TCSServiceTop draw rod bearingThe top bearing of the draw rod (1a) (“clipbearing”) can be
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 14TCSTop cutterThe top cutter (1) is attached to the carriage(3) by three screws (2).To re
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 15TCSBottom cutterTo be replaced, the bottom cutter isremoved from the rear of the TCS (1).
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 16TCS4. On each side, unscrew the two screws(2) and remove the slide blocks (1).5. Remove t
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 17TCSSetting the cutterTop cutter1. Loosen the motor attachment (1).2. Push a feeler gauge
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 18TCSBottom cutter1. Connect the stacker to the printer.2. Loosen bottom cutter setting scr
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 19TCSCarriage guideEndurance tests have shown that it is sensibleto replace the carriage gu
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 2TCSGeneral notesPurpose of the stackerThe TCS textile stacker is an auxiliary unit for use
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 20TCSAssemblyIn reverse order.Ensure that the guide parts arepositioned correctly!Press b
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 21TCSPusherTools– Allan keys, sizes 1.5 and 2.5Disassembling1. Open the plexiglass cover of
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 22TCSRight balancerDisassembling/assemblyRemoving the side part (1) eases access tothe righ
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 23TCSAnti-static brush/pusherDisassembling/assemblyThe anti-static brush has a strip of sel
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 24TCSMicroswitchWhile the stacker is operating, the materialsupport always slips further do
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 25TCSLid switchThe lid switch is positioned on the top edge ofthe stacker housing. A magnet
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 26TCSRetrofitting the type I materialguideThe modification kit replaces the retaining pinsu
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 27TCSTechnical specificationsMaterial widthTextile material 15 to 53 mmSelf-adhesivemateria
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 28TCSIndexAActivating /deactivating the textile stacker ..5Anti-static brush...
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 3TCSSafety notesCAUTION!Danger of cuts to hands and fingers!– Do not remove safety devices!
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 4TCSAttaching the stacker1. Switch the printer off and remove themains plug.2. Remove the p
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 5TCSSetting up the stackerActivating/deactivating the textile stackerAfter the textile stac
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 6TCS6678321Setting the stackerSetting the material width1. Measure the material width if un
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 7TCSFeeding in the material1. Push in the material end (1) between theslide plates (2, 3).2
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 8TCSMaintenanceLubricatingEvery now and again add a drop of very fine machine oil (e.g. sew
01/02 Rev. 2.13-02 MANUAL Attachment, Setup, Service, Page 9TCSServicing notesSafetyFor your own safety, you must observe the following instructions w
Comments to this Manuals