Avery Dennison Monarch 9433 SNP Instruction Manual

Monarch9433™Sierra Sport3™Printer®Operator’sHandbookOperator’sHandbookTC9433OH Rev. AD 12/07 ©2006 Paxar Americas, Inc. a subsidiary of Avery Dennison

1-6 Operator’s Handbook Note: Do not disassemble, short-circuit, heat above 80°C, or incinerate the battery. It may explode. ♦ The battery shou

Getting Started 1-7 Connecting the Communications Cables 9-pin serial communication cables and USB cables are available. For best results, use on

1-8 Operator’s Handbook Serial Cable 1. Plug the DB9 connector into the DB9 port. 2. Place the cable in the cable cavity. 3. Close the hinged

Getting Started 1-9 USB Cable 1. Plug the USB cable into the USB port. 2. Lock the cable in place by placing it behind the left screw post and in

1-10 Operator’s Handbook Using the Display and Buttons P Turns the printer on and off. F Advances the supply or returns the display to the next

Getting Started 1-11 Printing The host sends online packets containing print jobs to the printer. Make sure supplies are loaded. 1. Turn on the pr

1-12 Operator’s Handbook

Loading Supplies 2-1 LOADING SUPPLIES This chapter describes how to load supply for ♦ non-peel mode (prints a continuous strip of supply) ♦ peel mo

2-2 Operator’s Handbook Loading for Non-Peel Mode Use these instructions to load labels, tags, and receipt paper to print in a continuous strip. 1

Loading Supplies 2-3 Note: The supply should unwind from the top with the loose end of the supply feeding through the exit chute. 4. Pull out eno

Each product and program carries a respective written warranty, the only warranty on which the customer can rely. Paxar reserves the right to make ch

2-4 Operator’s Handbook 5. Close the supply door until the release levers click into place. 6. Press F to advance the supply. If you receive a sup

Loading Supplies 2-5 Loading for Peel Mode Use these instructions to print labels and separate them from the liner (on-demand). 1. Pull the releas

2-6 Operator’s Handbook Note: The supply should unwind from the top with the loose end of the supply feeding through the exit chute. 4. Raise the

Loading Supplies 2-7 6. Close the supply door until the release levers click into place. 7. Lightly tug on the liner to remove the slack. 8. Press

2-8 Operator’s Handbook Loading Fan-Fold Supplies Use these instructions to load fan-fold supply. 1. Pull the release levers located on both sides

Loading Supplies 2-9 8. Close the supply door until the release levers click into place. 9. Press F to advance the supply. If you receive a supply

2-10 Operator’s Handbook Caution: Do not touch the tear edge. You may cut yourself. Tearing the Supplies Tear the supply from the right or left us

Care & Maintenance 3-1 CARE & MAINTENANCE This chapter explains how to ♦ clean the printhead, platen roller, and supply sensors ♦ clear lab

3-2 Operator’s Handbook Use any of the following items to clean the printhead: ♦ A soft cloth moistened with isopropyl alcohol. Caution: Use isopr

Care & Maintenance 3-3 4. Clean the printhead with a clean soft cloth moistened with isopropyl alcohol, a cleaning pen, or a small brush. Note:

i TABLE OF CONTENTS GETTING STARTED ... 1-1 Using This Manual ...

3-4 Operator’s Handbook 6. Clean the platen roller with a clean soft cloth moistened with isopropyl alcohol or a cleaning pen. Turn the platen rolle

Care & Maintenance 3-5 Clearing Label Jams When you are printing and a jam occurs, a supply error message appears. To clear the jam: 1. Turn

3-6 Operator’s Handbook

Troubleshooting 4-1 TROUBLESHOOTING This chapter lists some of the common printer problems and their possible solutions. If these solutions do not w

4-2 Operator’s Handbook Common Errors The following is a list of common printer errors you may receive. If you receive a message not listed here,

Troubleshooting 4-3 Error Description 704 Check Supply Printer has not sensed a supply mark within the specified number of inches or is out of suppl

4-4 Operator’s Handbook Error Description 758 Check Supply Either the supply is not seen or the on-demand sensor is broken. Press A under x to clea

Specifications A-1 SPECIFICATIONS This appendix includes information about printer specifications and cable pin-outs. Printer Specifications Heigh

A-2 Operator’s Handbook Operating Limits 32° to 109° F (0° to 43° C) (Printer): Storage 14° to 122° F (-10° to 50° C) Relative Humidity (Batter

Specifications A-3 Supply Specifications Supply Types: Labels, tags, or receipt paper Supply Widths: 0.5" (13 mm) minimum 2.99" (76 m

ii ACCESSORIES ... B-1 Single Station Battery Charger ...

A-4 Operator’s Handbook

Accessories B-1 ACCESSORIES This appendix lists the accessories that work with your printer and briefly describes them. Use these part numbers when

B-2 Operator’s Handbook Single Station Battery Charger The Monarch® 9462™ Single Station Battery Charger charges one battery at a time. See Chapt

Printer Options C-1 PRINTER OPTIONS This appendix lists the options that may be installed in your printer. ♦ Linerless ♦ Bluetooth® Linerless The

C-2 Operator’s Handbook

Getting Started 1-1 GETTING STARTED The Monarch® Sierra Sport3™ 9433™ printer is a portable, thermal-direct printer that prints on tags, labels, or

1-2 Operator’s Handbook Additional Documentation A Quick Reference for this printer is available in the box. A Programmer's Manual and System

Getting Started 1-3 Installing the Battery The printer uses a 7.4V Lithium Ion battery. The battery can be installed with or without supplies load

1-4 Operator’s Handbook 2. Insert the connector end of the battery into the printer. 3. Close the supply door until the release levers click into

Getting Started 1-5 Battery and Safety Information ♦ You must charge a battery before using it. For optimal battery life, charge the battery withi