Avery Dennison Monarch 9460 Instruction Manual

Monarch®Sierra Sport™ 29460™ PrinterTC9460OH Rev. AG 12/07 ©2004 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp.All r ights reserved.

1-6 Getting Started CAUTION Do Not disassemble, short-circuit, heat above 80°C, or incinerate the battery. It may explode. ♦ The battery should be

Getting Started 1-7 Connecting the Communications Cable 9-pin and 25-pin serial communication cables are available. For best results, use only M

1-8 Getting Started 2. Plug the DB9 connector into the DB9 port. 3. Place the cable in the cable cavity. 4. Close the hinged cable door and tigh

Getting Started 1-9 Using the Display and Buttons P Turns the printer on and off. F Advances the supply or returns the display to the next high

1-10 Getting Started 2. Download a format and a batch. For information on creating packets and downloading print jobs refer to the online version of

Loading Supplies 2-1 LOADING SUPPLIES This chapter describes how to load supply for ♦ non-peel mode (prints on continuous strip of supply). ♦ pee

2-2 Loading Supplies 2. Remove the tape from a new roll of supply. 3. Push apart the supply holder tabs to widen the supply holders. Insert a roll

Loading Supplies 2-3 5. Close the supply door until the release buttons click into place. 6. Press F to calibrate the supply under the printhead.

2-4 Loading Supplies Loading for Peel Mode You need label supply with a liner to use these instructions. 1. Open the supply door by pushing down o

Loading Supplies 2-5 Note: The supply should unwind as shown with the loose end of the supply feeding through the exit chute. 4. Pull out enough

Each product and program carries a respective written warranty, theonly warranty on which the customer can rely. Paxar reserves theright to make chang

2-6 Loading Supplies 6. Close the supply door until the release buttons click into place. Note: The peel bar closes when the supply door clicks i

Care & Maintenance 3-1 CARE & MAINTENANCE This chapter explains how to ♦ clean the printhead, platen roller, and the supply sensors. ♦ cl

3-2 Care & Maintenance Use any of the following items to clean the printhead: ♦ A soft cloth moistened with isopropyl alcohol. CAUTION Use isopr

Care & Maintenance 3-3 4. Clean the printhead with a clean soft cloth moistened with isopropyl alcohol, a cleaning pen, or a small brush. CAUT

3-4 Care & Maintenance 7. Clean the on-demand and black mark sensor with a clean soft cloth or cotton swab moistened with isopropyl alcohol or a

Troubleshooting 4-1 TROUBLESHOOTING This chapter lists some of the common printer problems and their possible solutions. If these solutions do not

4-2 Troubleshooting Problem Solution Supply does not calibrate properly. Check the on-demand, black mark, die cut, or non-indexed sensors. Refer to

Troubleshooting 4-3 Error Description 614 Invalid Data Portion of field off supply or there may be an invalid character in the packet. 703 Check

4-4 Troubleshooting Error Description 757 Load Supplies Load supplies (supply length mismatch), because the calibrated supply length differs by plus

Specifications A-1 SPECIFICATIONS This appendix includes information about printer specifications and cable pin-outs. Printer Specifications Heigh

i TABLE OF CONTENTS GETTING STARTED ... 1-1 Introduction...

A-2 Specifications Operating Limits 40° to 104°F (5° to 40° C) (Printer): Storage 40° to 140° F (5° to 60° C) Storage Limits -4° to 95°F (-20° to

Specifications A-3 Supply Specifications Supply Types: Labels (standard or linerless), tags or receipt paper Supply Widths: 0.5" (13 mm) mi

A-4 Specifications

Accessories B-1 ACCESSORIES This appendix lists the accessories that work with your printer and briefly describes them. Use these part numbers when

B-2 Accessories Single Station Battery Charger The Monarch® 9462™ Single Station Battery Charger is designed for the Monarch® 9460™ portable printe

Printer Options C-1 PRINTER OPTIONS This appendix lists the options that may be installed in your printer. ♦ Linerless ♦ Bluetooth® Linerless T

C-2 Printer Options

ii ACCESSORIES ... B-1 Single Station Battery Charger ...

Getting Started 1-1 GETTING STARTED The Monarch® Sierra Sport2™ 9460TM printer is a portable, thermal-direct printer that prints on tags, labels, o

1-2 Getting Started Printer Utilities The Monarch® MPCLTM Toolbox utilities are also available on our Web site (www.paxar.com) and are free to down

Getting Started 1-3 Installing the Battery The battery can be installed with or without supplies loaded. Note: Make sure the battery is charged

1-4 Getting Started 4. Close the supply door until the release buttons click into place. 5. Turn on the printer by pressing and holding P until th

Getting Started 1-5 Battery and Safety Information ♦ You must charge a battery before using it. For optimal battery life, charge the battery with