Avery Dennison AP5.4 Gen II Service Manual Page 40
- Page / 103
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP 5.4 Gen II – AP 5.6
40
> COM1 PORT
Baud rate
AP5.4 AP5.6
Data transfer speed
Speed of data transfer using the serial interface.
xxxxxx Baud Setting range: 300 to 115200 Baud; Unit interval: 300/600/1200/2400/4800/
9600/19200/38400/115200 (default)
No. of data bits
AP5.4 AP5.6
This parameter can be defined in connection with both the serial and the par-
allel interface.
7 7 Data bits
8 8 Data bits
Parity
AP5.4 AP5.6
Defines the parity check of serial transmitted data.
The parity bit is for checking data transmission. If the check shows an error,
a corresponding message is displayed. The setting must be identical at the
sender and the receiver. Normally transmission is set without a parity bit.
Odd Odd parity.
A parity bit is added so that there is an odd number of 1 Bits.
Even Even parity.
A parity bit is added so that there is an even number of 1 Bits.
None No check bit. Sending and receiving without check bit.
Always zero Check bit is always 0 (zero). Sending and receiving without parity check.
Stop bits
AP5.4 AP5.6
Number of stop bits
Number of stop bits at the serial interface.
1 Bit 1 stop bit
2 Bit 2 stop bits
- PRINT INFO 1
- PRINT PARAMETERS 1
- INTERFACE PARA 1
- SYSTEM PARAMETERS 2
- I/O BOARD 2
- DISPENSER PARA 2
- REWINDER PARA 3
- MLI PARAMETERS 3
- SPECIAL FUNCTION 3
- SERVICE FUNCTION 3
- SERVICE DATA 3
- General Information 5
- Operating the parameter menu 7
- Parameter Menu 8
- Overview Parameter Menus 9
- AP 5.4 Parameters 10
- FW 7.34 Pre 4081 10
- Alphabetical Parameter List 13
- . . . . . . . . . . 73 14
- . . . . . . . . . . . . . 58 14
- Memory status 18
- on page 168 18
- Font status 19
- Flashdata status 22
- Service Status 23
- on page 159 23
- on page 164 23
- on page 165 23
- on page 157 23
- Dottest endless 24
- Dottest punched 24
- on page 25 24
- Reference label 25
- RFID Status 26
- Material type 28
- Material length 28
- Material width 28
- Print direction 29
- Punch offset 30
- Bar code multip 30
- ¯ In production mode only 31
- EAN sep. lines 32
- Rotated Barcodes 32
- Dispenseposition 32
- Cut mode 33
- SYSTEM PARAMETERS > 34
- Ribbon autoecon 34
- Cut speed 35
- Cut position 35
- Double cut 35
- Rewind direction 36
- X - Printadjust 36
- Y – Printadjust 36
- Punch mode 37
- Punch level 37
- Printer ID No 39
- Spooler size 39
- Offline mode 39
- Interface delay 39
- > COM1 PORT 40
- Baud rate 40
- No. of data bits 40
- Stop bits 40
- AP5.4 AP5.6 44
- ¯ Only in production mode 45
- FTP server 46
- FTP password 46
- WEB server 47
- WEB display refr 48
- WEB admin passw 48
- WEB supervisor p 48
- Time client 49
- Time server IP 49
- Sync. Interval 49
- DHCP host name 50
- > OPTIONS 50
- RFID Option 50
- StandAlone Input 50
- > DRIVEASSIGNMENT 51
- Character sets 53
- Character filter 54
- Light sens. type 54
- Head-sensor dist 54
- Sens. punch-LS 55
- Foil mode 55
- Turn-on mode 55
- Error reprint 55
- EasyPlug error 56
- Single job mode 56
- Head resistance 56
- Voltage offset 58
- Miss. label tol 58
- Gap detect mode 58
- Periph. device 59
- Singlestartquant 59
- External signal 59
- on page 102 60
- Print contrast 60
- Ram disk size 60
- Start print mode 60
- Font downl. area 61
- Free store size 62
- on page 18 62
- Print info mode 62
- Reprint function 62
- Language 63
- Keyboard 63
- Access authoriz 63
- [5] Permissible key codes 64
- Realtime clock 65
- Feed input 67
- Pause input 67
- Error output 67
- Error Polarity 68
- Status output 68
- on page 68 68
- Status polarity 68
- End print mode 69
- Display mode 72
- Dispense counter 72
- Application mode 72
- Start source 73
- Calibration mode 73
- Start offset 73
- Start rew. current 76
- Start cur. len 76
- Pullback current 76
- Delimiter Char 81
- Label Top 81
- Left Position 81
- Manual Calibrate 81
- Resolution 81
- Error Indication 82
- Error Checking 82
- Image Save Path 82
- Command ^PR 82
- Command ^MT 82
- Label Invert 83
- Command ^JM 83
- Command ^MD/~SD 83
- Delete spooler 85
- Factory settings 85
- Store Parameters 85
- Store Diagnosis 86
- Data blocks del 86
- EasyPl. file log 87
- Log files delete 87
- RFID stat. del 87
- Cutter exchange 89
- on page 24 89
- Serv. data reset 89
- EasyPlug monitor 89
- EP Monitor Mode 90
- Sensor adjust 90
- Sensor test 90
- Cutter test 90
- Memory card test 92
- Send test 93
- Receive test 94
- Rewinder adjust 95
- Printtest 95
- AP 5.4 Gen II – AP 5.6 100
- Default values 103
- on page 65 103
- Space for Jobs 103
- Max. Labellength 103
Related products and manuals for Label printers Avery Dennison AP5.4 Gen II
(18 pages)
(47 pages)© 2020, manymanuals.com. All rights reserved. | 0.867 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals