Avery Dennison AP5.4 Gen II Service Manual Page 7
- Page / 103
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP 5.4 Gen II – AP 5.6
7
Operating the parameter menu
The illustrations on the following pages clarifie the operating principle of the
parameter menu. The return path shown on the left of the screen, called up
using the Prog. button, also applies for parameters in the middle of the
screen.
Setting values The setting of a parameter always follows this scheme:
1. Select the parameter.
2. Press the Online button.
3. Set the parameter to the intended value by pressing the Cut or Feed button.
4. Confirm by pressing the Online button.
Example
Setting the parameter PRINT PARAMETERS > Material type to punched material.
1. Press prog button.
2. Press prog button.
3. Press cut button.
4. Press online button.
5. Press cut button repeatedly, until the following is displayed:
6. Press feed button.
7. Press online button.
8. Press prog button 2x.
OFFLINE 0 JOBS Initial state: off-line mode
PRINT INFO
PRINT PARAMETERS
PRINT PARAMETERS
Print speed
First parameter in the PRINT PARAMETERS menu.
Material type
Endless
Material type
Punched
Setting the parameter to the intended value by
pressing the Cut or Feed button.
PRINT PARAMETERS
Material type
Confirm with Online button.
OFFLINE 0 JOBS "Way back" by pressing the Prog button.
- PRINT INFO 1
- PRINT PARAMETERS 1
- INTERFACE PARA 1
- SYSTEM PARAMETERS 2
- I/O BOARD 2
- DISPENSER PARA 2
- REWINDER PARA 3
- MLI PARAMETERS 3
- SPECIAL FUNCTION 3
- SERVICE FUNCTION 3
- SERVICE DATA 3
- General Information 5
- Operating the parameter menu 7
- Parameter Menu 8
- Overview Parameter Menus 9
- AP 5.4 Parameters 10
- FW 7.34 Pre 4081 10
- Alphabetical Parameter List 13
- . . . . . . . . . . 73 14
- . . . . . . . . . . . . . 58 14
- Memory status 18
- on page 168 18
- Font status 19
- Flashdata status 22
- Service Status 23
- on page 159 23
- on page 164 23
- on page 165 23
- on page 157 23
- Dottest endless 24
- Dottest punched 24
- on page 25 24
- Reference label 25
- RFID Status 26
- Material type 28
- Material length 28
- Material width 28
- Print direction 29
- Punch offset 30
- Bar code multip 30
- ¯ In production mode only 31
- EAN sep. lines 32
- Rotated Barcodes 32
- Dispenseposition 32
- Cut mode 33
- SYSTEM PARAMETERS > 34
- Ribbon autoecon 34
- Cut speed 35
- Cut position 35
- Double cut 35
- Rewind direction 36
- X - Printadjust 36
- Y – Printadjust 36
- Punch mode 37
- Punch level 37
- Printer ID No 39
- Spooler size 39
- Offline mode 39
- Interface delay 39
- > COM1 PORT 40
- Baud rate 40
- No. of data bits 40
- Stop bits 40
- AP5.4 AP5.6 44
- ¯ Only in production mode 45
- FTP server 46
- FTP password 46
- WEB server 47
- WEB display refr 48
- WEB admin passw 48
- WEB supervisor p 48
- Time client 49
- Time server IP 49
- Sync. Interval 49
- DHCP host name 50
- > OPTIONS 50
- RFID Option 50
- StandAlone Input 50
- > DRIVEASSIGNMENT 51
- Character sets 53
- Character filter 54
- Light sens. type 54
- Head-sensor dist 54
- Sens. punch-LS 55
- Foil mode 55
- Turn-on mode 55
- Error reprint 55
- EasyPlug error 56
- Single job mode 56
- Head resistance 56
- Voltage offset 58
- Miss. label tol 58
- Gap detect mode 58
- Periph. device 59
- Singlestartquant 59
- External signal 59
- on page 102 60
- Print contrast 60
- Ram disk size 60
- Start print mode 60
- Font downl. area 61
- Free store size 62
- on page 18 62
- Print info mode 62
- Reprint function 62
- Language 63
- Keyboard 63
- Access authoriz 63
- [5] Permissible key codes 64
- Realtime clock 65
- Feed input 67
- Pause input 67
- Error output 67
- Error Polarity 68
- Status output 68
- on page 68 68
- Status polarity 68
- End print mode 69
- Display mode 72
- Dispense counter 72
- Application mode 72
- Start source 73
- Calibration mode 73
- Start offset 73
- Start rew. current 76
- Start cur. len 76
- Pullback current 76
- Delimiter Char 81
- Label Top 81
- Left Position 81
- Manual Calibrate 81
- Resolution 81
- Error Indication 82
- Error Checking 82
- Image Save Path 82
- Command ^PR 82
- Command ^MT 82
- Label Invert 83
- Command ^JM 83
- Command ^MD/~SD 83
- Delete spooler 85
- Factory settings 85
- Store Parameters 85
- Store Diagnosis 86
- Data blocks del 86
- EasyPl. file log 87
- Log files delete 87
- RFID stat. del 87
- Cutter exchange 89
- on page 24 89
- Serv. data reset 89
- EasyPlug monitor 89
- EP Monitor Mode 90
- Sensor adjust 90
- Sensor test 90
- Cutter test 90
- Memory card test 92
- Send test 93
- Receive test 94
- Rewinder adjust 95
- Printtest 95
- AP 5.4 Gen II – AP 5.6 100
- Default values 103
- on page 65 103
- Space for Jobs 103
- Max. Labellength 103
Related products and manuals for Label printers Avery Dennison AP5.4 Gen II
(18 pages)
(47 pages)© 2020, manymanuals.com. All rights reserved. | 1.281 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals