Avery Dennison SNAP 600 User Manual Page 19
- Page / 141
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
User’s Manual—SNAP™ 600 Printer
19
2.5.5 Installing PCMate Platinum Software
The software used to drive the AVERY DENNISON family of printers is covered
in a separate manual. The PCMate Platinum software is a Windows
®
application
used to create formats for the AVERY DENNISON SNAP 600 printer as well as
all other AVERY DENNISON control printers.
The printer is also capable of operating directly from a mainframe when using
the RS232 interface and AVERY DENNISON's command language (PCL).
NOTE: When using PCMate Platinum with virtual control /
display interface, the remote control / display module will
function. However, it is only needed when the printer is
driven by a mainframe computer or other software
interface packages.
2.6 Printing a Test Label
2.6.1 Loading Supplies
Before you can print a test label, the printer must be loaded with stock and ink.
Refer to section 3.1 for instructions on loading the stock and ink.
2.6.2 Turning the Printer on
Turn the power switch on. The power switch is located on the back of the
printer, just above the power cord.
The four lights on the Printer Control Panel will come on for a few seconds, and
then all four lights will start to flash. This indicates that the printer is performing
its internal diagnostic tests. After several seconds, the lights will stop flashing
and the Ready light will come on. This indicates that the printer is ready.
If any problems occur, see sections 9 and 10, Troubleshooting.
2.6.2 Selecting the Test Format
There are two test formats built into the printer. These are selected using the
Option Menu System. The steps below describe how to select one of the test
formats. For more information on the Option Menu System, see section 3.4.
When the instructions say to press a button, press the
button for a short time and release it. When the
instructions say to press and hold a button, press the
button and hold it down until the printer responds.
When you are in the Option Menu System, you can get out
by pressing and holding the Voice button until the printer
says “Returning to print mode.”
- 600 1
- Manual Part Number 591398 2
- Table of Contents 3
- 4.0 MAKING ADJUSTMENTS 38 4
- 5.0 MAINTENANCE 47 4
- APPENDICES 79 6
- 2.0 Installation 10
- 2.2 Receiving 12
- 2.3 Unpacking 12
- 2.4 Printer Description 14
- 2.5 Setting Up the Printer 16
- 18
- 2.6 Printing a Test Label 19
- 3.0 Operation 21
- 3.1.3 Loading the Stock 24
- 3.1.4 Butt Splice 26
- 3.3 Printing Labels 27
- 3.3.2 Printing 28
- 3.3.3 Errors 28
- 3.3.4 End of Day 29
- 3.3.5 Clearing Print Jobs 29
- 3.4 Option Menu System 31
- 3.4.1 Running Test Labels 33
- 3.4.2 Using Voice Demos 35
- 4.0 Making Adjustments 38
- 4.2 Adjusting the Stacker 39
- 4.2.1 Stacker Position 40
- 4.2.2 Toggle Switch 40
- 4.2.3 Stacker Angle 40
- 4.3.1 Cut Adjust 42
- 4.4 Printer Features 43
- 5.0 Maintenance 47
- 5.1.2 Cleaning Procedures 48
- 5.2 Print Head Replacement 49
- 5.3 Lubrication 52
- 5.4 Rotary Knife Assembly 52
- Retaining Screw 53
- 6.0 Service Adjustments 55
- 7.1 Controlling the Printer 58
- 7.2 The Menu System 58
- 7.3 Changing Values 58
- 8.0 Virtual Control Panel 60
- 9.1 Introduction 62
- 9.2 What is Needed 62
- 9.3 Getting the UPG file 62
- 9.5 Performing the Upgrade 63
- 10.2 Stock / Ink Advance 68
- 10.3 Print 69
- 10.4 Cut / Stack 71
- 10.5 Printer Errors 72
- 11.1 Stock 76
- 11.2 Ink 77
- 11.3 Print 77
- 11.4 Knife 77
- Appendices 79
- FUSE WARNING 80
- Power Supply 81
- Voltage Selector Switch 81
- Value Transfer Type 82
- 3. Printer Specifications 84
- Platinum 85
- Platinum 85
- Reflective Sensor 590013(F) 86
- Reflective Sensor 590010(F) 87
- SENSOR SLIDE MOUNT BRACKET 88
- SHAFT, WEB GUIDE 88
- 8-32 X 3/8 CAP SCREW 88
- OPTIONAL BOTTOM 89
- REFLECTIVE 89
- 3/4 DIAMETER HOLE 92
- "O" RING 93
- SLIDE SHAFT 93
- FIBER-OPTIC CABLE 93
- 7/32 E-RING 95
- PLASTIC NUT 95
- SCRIBE TEMPLATE 96
- SCRIBE AND REMOVE 96
- THIS MATERIAL 96
- BASE VERIFIER MOUNT BRACKET 98
- 10-32 X 1/2 CAP SCREW 98
- (2) 10-32 X 3/4 CAP SCREW 98
- UPPER VERIFIER MOUNT BRACKET 98
- 6-32 X 3/8 CAP SCREW (4) 99
- VERIFIER MOUNT PLATE 99
- VERIFIER 99
- Installation – Rear Cover 101
- Assembly & Parts List 102
- 7. Warranty Policy 106
- Service 107
- Electrical Assembly Drawings 111
- Electrical System Schematic 114
- SEE NOTE 7 115
- Mechanical Assembly Drawings 117
- Ink Rewind Assembly 128
- Upright Frame Assembly 130
- Covers Assembly 132
- Feed – Drive Train Assembly 134
- Product / Services 141
- Installation Report 141
Related products and manuals for Print & Scan Avery Dennison SNAP 600
(135 pages)© 2020, manymanuals.com. All rights reserved. | 1.535 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals