Avery Dennison SNAP 600 User Manual Page 29
- Page / 141
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
User’s Manual—SNAP™ 600 Printer
29
3.3.4 End of Day
When the printer finishes printing all the print jobs that have been sent, it will
stop with a few labels left to print. This allows you to send another next print job
and print it without wasting stock and ink. The Data light will flash to indicate
this condition.
When this occurs, you may send another print job. The printer will start up
automatically.
If you are finished for the day or you need to change stock or ink for the next
print job, press the Start Button. The printer will print the last few labels of the
last print job. You can then turn off the printer or change the stock and ink for
the next print job.
3.3.5 Clearing Print Jobs
If you have sent print jobs to the printer and do not want to print the labels, press
and hold both the Start/Stop and Voice buttons simultaneously. After about 2
seconds, the printer will say “Clearing Current Batch.” If there is only one print
job, the Data light will go out.
If there are more than one print job and you only want to clear the current one,
release the buttons.
If there are more than one print job and you want to clear them all, continue to
hold the buttons until the printer says, “Clearing All Batches.”
3.3.6 Using Pre-Printed Stock
When using pre-printed stock, the printer must detect a sense mark on the stock
in order to print in the proper place. There are five methods for detecting the
sense mark - two standard methods and three optional methods.
• The AVERY DENNISON 600 printer has two through-hole sensors
standard with each printer. One sensor is mounted in the web guides
and will detect a hole or slot on the inside edge of the stock. This system
moves with the web guides so it is necessary for the web guides to be
properly adjusted. The other sensor will detect a hole or slot centered on
the stock. Choosing between these systems is controlled by a toggle
switch located on the right end of the printer between the printer and the
stacker. Pressing the top of the switch will select the edge sensor, and
pressing the bottom of the switch will select the center sensor.
• A top reflective sensor is available as an option. This sensor is fixed in
the center of the left web guide shaft and will detect a black sense mark
printed on the top of either tape or tag stock.
• A bottom reflective sensor is available as an option. This is installed in a
bracket assembly mounted directly below the left web guide roller and is
- 600 1
- Manual Part Number 591398 2
- Table of Contents 3
- 4.0 MAKING ADJUSTMENTS 38 4
- 5.0 MAINTENANCE 47 4
- APPENDICES 79 6
- 2.0 Installation 10
- 2.2 Receiving 12
- 2.3 Unpacking 12
- 2.4 Printer Description 14
- 2.5 Setting Up the Printer 16
- 18
- 2.6 Printing a Test Label 19
- 3.0 Operation 21
- 3.1.3 Loading the Stock 24
- 3.1.4 Butt Splice 26
- 3.3 Printing Labels 27
- 3.3.2 Printing 28
- 3.3.3 Errors 28
- 3.3.4 End of Day 29
- 3.3.5 Clearing Print Jobs 29
- 3.4 Option Menu System 31
- 3.4.1 Running Test Labels 33
- 3.4.2 Using Voice Demos 35
- 4.0 Making Adjustments 38
- 4.2 Adjusting the Stacker 39
- 4.2.1 Stacker Position 40
- 4.2.2 Toggle Switch 40
- 4.2.3 Stacker Angle 40
- 4.3.1 Cut Adjust 42
- 4.4 Printer Features 43
- 5.0 Maintenance 47
- 5.1.2 Cleaning Procedures 48
- 5.2 Print Head Replacement 49
- 5.3 Lubrication 52
- 5.4 Rotary Knife Assembly 52
- Retaining Screw 53
- 6.0 Service Adjustments 55
- 7.1 Controlling the Printer 58
- 7.2 The Menu System 58
- 7.3 Changing Values 58
- 8.0 Virtual Control Panel 60
- 9.1 Introduction 62
- 9.2 What is Needed 62
- 9.3 Getting the UPG file 62
- 9.5 Performing the Upgrade 63
- 10.2 Stock / Ink Advance 68
- 10.3 Print 69
- 10.4 Cut / Stack 71
- 10.5 Printer Errors 72
- 11.1 Stock 76
- 11.2 Ink 77
- 11.3 Print 77
- 11.4 Knife 77
- Appendices 79
- FUSE WARNING 80
- Power Supply 81
- Voltage Selector Switch 81
- Value Transfer Type 82
- 3. Printer Specifications 84
- Platinum 85
- Platinum 85
- Reflective Sensor 590013(F) 86
- Reflective Sensor 590010(F) 87
- SENSOR SLIDE MOUNT BRACKET 88
- SHAFT, WEB GUIDE 88
- 8-32 X 3/8 CAP SCREW 88
- OPTIONAL BOTTOM 89
- REFLECTIVE 89
- 3/4 DIAMETER HOLE 92
- "O" RING 93
- SLIDE SHAFT 93
- FIBER-OPTIC CABLE 93
- 7/32 E-RING 95
- PLASTIC NUT 95
- SCRIBE TEMPLATE 96
- SCRIBE AND REMOVE 96
- THIS MATERIAL 96
- BASE VERIFIER MOUNT BRACKET 98
- 10-32 X 1/2 CAP SCREW 98
- (2) 10-32 X 3/4 CAP SCREW 98
- UPPER VERIFIER MOUNT BRACKET 98
- 6-32 X 3/8 CAP SCREW (4) 99
- VERIFIER MOUNT PLATE 99
- VERIFIER 99
- Installation – Rear Cover 101
- Assembly & Parts List 102
- 7. Warranty Policy 106
- Service 107
- Electrical Assembly Drawings 111
- Electrical System Schematic 114
- SEE NOTE 7 115
- Mechanical Assembly Drawings 117
- Ink Rewind Assembly 128
- Upright Frame Assembly 130
- Covers Assembly 132
- Feed – Drive Train Assembly 134
- Product / Services 141
- Installation Report 141
Related products and manuals for Print & Scan Avery Dennison SNAP 600
(135 pages)© 2020, manymanuals.com. All rights reserved. | 0.715 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals